China high quality Ngcl Drum Shape Gear Coupling with Brake Wheel wide angle pto shaft

Product Description

NGCL Drum Gear Coupling With Brake Wheel

NGCL Drum Gear Coupling With Brake Wheel is a drum gear coupling. It has a brake wheel, which can control the rotation speed of the machine by controlling the speed of the brake wheel. NGCL Drum Gear Coupling With Brake Wheel allows greater angular displacement, can improve the tooth contact conditions, and improve the ability to transfer torque, prolong the service life, with angular displacement along the contact state of gear width, consisting of inner gear and the same number of teeth of the flange half band coupling parts etc..
     
NGCL Drum Gear Coupling With Brake Wheel need to work in good and sealed conditions. NGCL Drum Gear Coupling With Brake Wheel has the same radial size and large bearing capacity as the toothed coupling. It is commonly used for shafting transmission under low speed and heavy load conditions. The high accuracy and dynamic balancing gear coupling can be used for high speed transmission.
 

·NGCL Drum Gear Coupling Main Dimension And Parameter(JB/ZQ4644-1997)

Type
 
Nominal torque
(kn·m)
Allow speed
(R/min)
Shaft hole diameter Shaft hole length D0 D D1 D2 C C1 H B B1 B2 B3 Weight Rotary inertia
Kg.m2
dZ d1,d2 Y J1type
NGCL1 355 4000 20-35 20,22,24 52 38 160 103 71 50 30 8 2 56 42 38 68 7 0.07
NGCL2 630 4000 25-45 25,28 62 44 160 115 83 60 36 8 2 68 48 42 68 9 0.079
NGCL3 1000 3800 30-55 28 62 44 200 127 95 75 41 8 2 70 49 42 85 14.6 0.181
NGCL4 1600 3800 40-65 38 82 60 200 149 116 90 41 8 2 74 53 42 85 18.6 0.225
NGCL5 2800 3000 45-75 40,42,45 112 84 250 167 134 105 48 8 2.5 84 58 42 105 31.8 0.58
NGCL6 4500 3000 50-90 60,63,65 142 107 250 187 153 125 49 9 2.5 85 59 42 105 38.5 0.754
NGCL7 6300 2400 60-100 80,85,90 172 132 315 204 170 140 53 9 2.5 93 63 42 132 61.8 1.299
NGCL8 9000 1900 70-110 100,110 212 167 400 230 186 155 64 12 3 112 77 47 168 108 4.072
NGCL9 14000 1500 80-130 130 252 202 500 256 212 180 71 13 3 119 80 47 210 167 10.109
NGCL10 20000 1200 80-150 130,140,
150
252 202 630 287 239 200 65 15 3.5 120 90 47 265 237 29.248
NGCL11 31500 1050 100-170 160,170 302 242 710 325 276 235 77 16 3.5 134 94 47 298 357 47.08
NGCL12 45000 1050 100-200 190,200 352 282 710 362 313 270 94 17 4 164 104 49 298 464 53.69
NGCL13 63000 950 150-220 200,220 352 282 800 412 350 300 88 18 4.5 165 113 49 335 596 86.67
NGCL14 1000000 950 170-220 240,250 410 330 800 462 420 335 92 20 5.5 209 157 63 335 785 105.9

♦Product Show
 

Other Products List

Transmission Machinery 
Parts Name
Model
Universal Coupling WS,WSD,WSP
Cardan Shaft SWC,SWP,SWZ
Tooth Coupling CL,CLZ,GCLD,GIICL,
GICL,NGCL,GGCL,GCLK
Disc Coupling JMI,JMIJ,JMII,JMIIJ
High Flexible Coupling LM
Chain Coupling GL
Jaw Coupling LT
Grid Coupling JS

Our Company

HangZhou CZPT Machinery Manufacturing Co., Ltd. is a high-tech enterprise specializing in the design and manufacture of various types of coupling. There are 86 employees in our company, including 2 senior engineers and no fewer than 20 mechanical design and manufacture, heat treatment, welding, and other professionals.

Advanced and reasonable process, complete detection means. Our company actively introduces foreign advanced technology and equipment, on the basis of the condition, we make full use of the advantage and do more research and innovation. Strict to high quality and operate strictly in accordance with the ISO9000 quality certification system standard mode.

Our company supplies different kinds of products. High quality and reasonable price. We stick to the principle of “quality first, service first, continuous improvement and innovation to meet the customers” for the management and “zero defect, zero complaints” as the quality objective.

Our Services
1.Design Services
Our design team has experience in cardan shaft relating to product design and development. If you have any needs for your new product or wish to make further improvements, we are here to offer our support.

2.Product Services
raw materials → Cutting → Forging →Rough machining →Shot blasting →Heat treatment →Testing →Fashioning →Cleaning→ Assembly→Packing→Shipping

3.Samples Procedure
We could develop the sample according to your requirement and amend the sample constantly to meet your need.

4.Research & Development
We usually research the new needs of the market and develop the new model when there is new cars in the market.

5.Quality Control
Every step should be special test by Professional Staff according to the standard of ISO9001 and TS16949.

FAQ
Q 1: Are you trading company or manufacturer?
A: We are a professional manufacturer specializing in manufacturing
various series of couplings.

Q 2:Can you do OEM?
Yes, we can. We can do OEM & ODM for all the customers with customized artworks of PDF or AI format.

Q 3:How long is your delivery time?
Generally it is 20-30 days if the goods are not in stock. It is according to quantity.

Q 4: Do you provide samples ? Is it free or extra ?
Yes, we could offer the sample but not for free.Actually we have a very good price principle, when you make the bulk order then cost of sample will be deducted.

Q 5: How long is your warranty?
A: Our Warranty is 12 month under normal circumstance.

Q 6: What is the MOQ?
A:Usually our MOQ is 1pcs.

Q 7: Do you have inspection procedures for coupling ?
A:100% self-inspection before packing.

Q 8: Can I have a visit to your factory before the order?
A: Sure,welcome to visit our factory.

Q 9: What’s your payment?
A:1) T/T. 

Contact Us
Web: huadingcoupling
Add: No.11 HangZhou Road,Chengnan park,HangZhou City,ZheJiang Province,China
 

Standard Or Nonstandard: Standard
Shaft Hole: 19-32
Torque: >80N.M
Bore Diameter: 19mm
Speed: 4000r/M
Structure: Rigid
Samples:
US$ 500/Piece
1 Piece(Min.Order)

|
Request Sample

Customization:
Available

|

Customized Request

Shaft Collar

PTO Shaft Safety Chains

PTO shaft is the part of a tractor that helps transfer power from the tractor to the equipment it is hooked to. A PTO shaft is important if you have a tiller or bush hog. The correct PTO shaft size is crucial for both the tractor and the equipment. If the PTO shaft size is not correct for your equipment, it may not work.
Shaft Collar

Safety chains

<br/Safety chains are an essential part of securing your PTO shaft. They prevent a rotating plastic shield from coming loose and causing injury or damage. It is important to protect your PTO and any other drive shafts on your machine. Watch the video below for more information about the dangers of unguarded PTOs.
PTOs are an efficient way to transfer mechanical power between tractors and implements. They helped revolutionize North American agriculture during the 1930s. Despite their convenience, PTOs have also proven to be one of the most common farm machinery hazards. This fact sheet outlines several important PTO safety precautions.
Safety chains for PTO shafts are necessary to protect both tractor and implement from damage. The PTO shaft must be attached properly to the tractor and the implement before starting the equipment. Before operating, be sure that the safety chains are positioned in a way that allows them to fully move. When operating the PTO, avoid being too aggressive as this can damage the drive line and shaft. For further safety, make sure to fit a torque limiter or clutch on the implement end of the PTO shaft.
PTOs are great for plowing, mowing, and shredding, but they also have potential to cause injuries if you don’t use a safety chain. It’s best to get a chain that is long enough to prevent injuries. Also, be sure that the PTO shaft does not compress completely at any point during the operating range. There should be several inches of overlap in the longest operating extension of the PTO.
Another common hazard with PTOs is IID shafts. While many machines and tractors have driveline guards, these are often missing. If you have a PTO with an IID, you should consider installing a safety chain.

Shield

A swingable tractor PTO shaft shield assembly consists of an inverted U-shaped shield member slidably attached to a bracket. It extends above the PTO shaft and has several notches and pins that engage each other. It can be held in a number of positions and can be retracted when not in use. It also includes a cover member that covers the space between the shield and tractor and abuts the raised portion of the shield member.
The PTO shaft shield is typically made of plastic, but it can also be made of metal. Plastic is less likely to break or damage than metal. The shield is supported by a bracket 51 with a curved distal end 57 and a non-metallic guard 59. When used in conjunction with a bracket, a PTO shaft shield should be properly installed to prevent damage to the shaft.
Keeping the PTO shaft shield in good condition is crucial to the safety of your tractor and your workers. An improperly installed PTO shaft shield can result in severe injuries. It may also ensnare or strike people in the vicinity. Proper maintenance will prevent many of these injuries. Equipment manufacturers have made great strides in reducing the risks of PTO mishaps. Operators are also responsible for keeping the shields in good condition. Removing the guards will only increase the risk to the operator.
A PTO shaft shield is a tubular assembly that is mounted on the tractor PTO shaft. It consists of two telescopic pieces that are held in place by shield support bearings. This shield protects the PTO shaft and the universal joints from debris and prevents premature wear. The shield can be easily removed and replaced if necessary.
Shaft Collar

IID shaft guard

The IID shaft guard is a safety device used to protect PTO powered machinery from the possibility of separating while in use. The shaft, which is a telescoping shaft, is attached to the PTO stub on tractors. The telescopic feature is convenient when moving across uneven ground. However, this type of shaft can cause serious injury if it separates while in use.
The IID shaft guard can prevent these injuries by completely covering the shaft. The guard is made of metal or plastic and rotates along with the shaft. A person can react in less than five tenths of a second, making the IID shaft guard an important part of PTO safety.
PTO shafts rotate at speeds as high as 540 rpm, which is very fast. A limb could be wrapped around the driveline shaft, causing a serious injury or death. Because of the speed of a PTO, it can be difficult for an individual to discern whether it is engaged or not and may not be aware of the danger.
An IID shaft guard should be fitted to every tractor PTO shaft. It should be tested and rotated regularly. It is also important to keep the tractor engine off when working around the PTO shaft. Using a drawbar to protect driveline components is also important. It will prevent stress on the driveline and reduce the possibility of separation.

Overrunning clutch

An overrunning clutch on a PTO shaft is a mechanism that allows the PTO shaft to rotate freely in one direction while restricting the speed of the implement being hauled behind the tractor. This clutch is also useful for preventing the speed of the implement from exceeding the speed of the tractor while slowing down. It comes in two basic configurations, one for a clockwise and the other for a counter-clockwise direction.
Another type of overrun clutch is used on tractors with a PTO driven bush hog. A bush hog has a flywheel and blades that drive the transmission through the PTO shaft. Without an overrunning clutch, these implements would freewheel while the tractor is driving and would potentially break the shaft.
A PTO overrunning clutch prevents power from backfeeding into the transmission, the part that transmits power to the rear wheels. Without an overrunning clutch, the tractor could backfeed power, causing an accident if the blade assembly hits an object. As such, it is essential to use the overrunning clutch to ensure that your tractor will be safe.

Direction of rotation

Despite its name, the direction of rotation of a PTO shaft can change if necessary. Most PTOs have a single-direction rotation, but you can often reverse the direction by installing a reverse PTO adapter. However, you should only use reverse PTOs when absolutely necessary.
A standard PTO rotation direction has been defined by the International Organization for Standardization (ISO). It is considered necessary to adhere to this standard, as improper rotation can cause damage to implements attached to a PTO. This standard helps farmers avoid problems such as ruined implements. While the direction of rotation of a PTO shaft is not always the same for all PTOs, there are some tractors that allow it to rotate both ways, while others have no restrictions.
The direction of rotation of a PTO shaft can be changed by using a hydraulic pump. Another way to connect a PTO is through a “sandwich” type split shaft unit. These units are mounted between the transmission and engine, and they usually receive drive directly from the engine shaft. They can also deliver complete engine power to a PTO. However, you must modify your vehicle’s driveline to install such a split-shaft unit.
China high quality Ngcl Drum Shape Gear Coupling with Brake Wheel   wide angle pto shaftChina high quality Ngcl Drum Shape Gear Coupling with Brake Wheel   wide angle pto shaft
editor by CX 2023-05-31

shaft pto

As one of leading shaft pto manufacturers, suppliers and exporters of mechanical products, We offer shaft pto and many other products.

Please contact us for details.

Mail:[email protected]

Manufacturer supplier exporter of shaft pto

Recent Posts